EN
Home
>Products
/ Power management
/ Power switches
/ Single-Channel load switches

AW35114FDR

2A Ultra-small Load Switch with Slew Rate Control

Datasheet :
Preview - AW35114FDR - Datasheet

Product details

Parameters

Channel 1
Controlled Slew Rate YES
Enable Logic Active Low
Output Discharge YES
Reverse Current Block NO
TR (μs) 274
Max Continuous Current (A) 2
Ron (mΩ) 64
Power Supply (Min) (V) 1
Power Supply (Max) (V) 5.5
Temperature -40℃~85℃
IO Level (V) 1.8
Package (mm) FCDFN 0.8X0.8-4L

Package | Pins | Size

FCDFN 0.8X0.8-4L

Features

● Integrated P-channel MOSFET load switch ● Input voltage: 1V to 5.5V ● 2A maximum continuous switch current ● Switch on-resistance(typ.): Rdson=52mΩ at VIN=5.5V Rdson=57mΩ at VIN=4.2V Rdson=64mΩ at VIN=3.3V Rdson=76mΩ at VIN=2.5V Rdson=100mΩ at VIN=1.8V Rdson=164mΩ at VIN=1.2V Rdson=230mΩ at VIN=1V ● Controlled slew rate to limit inrush currents ● Ultra low shutdown current ● Internal EN pull-down/up resistor ● Quick Output Discharge(QOD) for AW35111/ AW35113/AW35114 ● Full time Reverse Current Protection (RCP) for AW35112/AW35112B/AW35113 ● FCDFN 0.8mm×0.8mm-4L package FOWLP 0.8mm×0.8mm-4B package FOWLP 0.9mm×0.9mm-4B package

Description

The AW3511X family load switch integrates a 64mΩ (typ.) P-channel MOSFET, which can operate over a wide input range of 1V to 5.5V. The AW3511X features output slew rate control, limiting inrush currents during turn-on to protect downstream devices. In addition, AW35111/ AW35113/AW35114 have QOD function which can prevent the output from floating when the switch is disabled. A smart pull-down/up resistor is used to the EN pin during initial power-up and disconnects once the EN pin voltage reaches the VIH level, then the standby current is very low and power loss can be reduced. There is a Reverse Current Protection(RCP) function for AW35112/AW35112B/AW35113 when VOUT is 33mV(typ.) greater than VIN, which can prevent the current to flowing through the P-FET or the body diode. There is no output discharge resistor for AW35112 and AW35112B. The AW35111FDR/112FDR/113FDR/114FDR is available in FCDFN 0.8mm×0.8mm-4L package, and the AW35111FOR/112BFOR is available in FOWLP 0.8mm×0.8mm-4B package, and the AW35113FOR is available in FOWLP 0.9mm×0.9mm-4B package.

Technical documentation
Type
Title
Language
Date
Datasheet DS_AW3511X_EN_V1.8 英文   2026-07-23

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

Evaluation board

Load Switch EVB V1.1 — Load Switch EVB is the evaluation board of load switch series AW3511X. The key test points of the chip are led out separately on the test board for convenient testing.

EVB evaluation board for load switch series AW3511X

View options
Hardware development

Evaluation board

Load Switch EVB V1.1 — Load Switch EVB is the evaluation board of load switch series AW3511X. The key test points of the chip are led out separately on the test board for convenient testing.

EVB evaluation board for load switch series AW3511X

View options