EN
Home
>Products
/ Haptic
/ Haptic drivers
/ Boost haptic

AW86937FCR

11V Fast Startup With F0 Detect And Tracking LRA Haptic Driver

Datasheet :
Preview - AW86937FCR - Datasheet
Ref.Price
  • 1-99￥14.19
  • 100-249￥11.64
  • 250-499￥9.37
  • 500-999￥7.38
  • 1000+￥5.68

Product details

Voltage Type Boost
Vout (Max) (V) 11
SRAM (kB) 8
Istandby (μA) 4
IO Level (V) 1.2 1.8 3.3
AAE YES
Input Signal IIS IIC 3TRIG
LRA Calibration LCC3.0
Temperature -40℃~85℃
TikTap YES
Package (mm) FCQFN 2.5X2-18L
FCQFN 2.5X2-18L(0.55)
 1MHz I2C Bus  8-KByte Memory  8k/12k/24k/48k input wave sampling rate  F0 detect and tracking  Advance autobrake engine integrated  Playback mode:  Real time playback(Up to 4KByte FIFO)  Auto dynamic sine playback  Memory playback  3 Trigger playback  One wire playback  Cont playback  I2S/TDM playback  Resistance-Based LRA Diagnostics  Drive signal monitor for LRA protect  Drive Compensation Over Battery Discharge  Fast Start Up Time ＜1ms  Boost output voltage up to 11V  VOUT=8.8V@Vbat=4.2V for 8Ω LRA  Standby current：4uA@Vbat=4.2V  Supply voltage range 2.7 to 5.5V  Short-Circuit Protection, Over-Temperature Protection, Under-Voltage, Battery Protection  AW86937AFCR and AW86938ACSR include Immersion IP license for mobile phones and wearables  AW86937NFCR include Immersion IP license for notebook
AW8693X is a high voltage H-bridge, single chip LRA haptic driver, with F0 detecting and tracking based on BEMF, with a boost converter up to 11V drive voltage inside, supporting real time playback, auto dynamic sine playback, memory playback, cont playback, one wire playback, I2S/TDM playback and hardware pin trigged playback. A typical startup time of 1ms makes the AW8693X an ideal haptic driver for fast responses. AW8693X integrates a 8KByte SRAM for user-defined waveforms to achieve a variety of vibration experiences, supporting 4 sampling rate(8k/12k/24k/48k) of waveforms loaded in SRAM, supporting output waveform sampling rate up-sampling to 48k. AW8693X integrates an autobrake engine to suppress the aftershocks to zero for different drive waveforms(short or long) on different LRA motors. AW8693X supports LRA fault diagnostic based on resistance measurement and protections of short-circuit, over-temperature and under-voltage. AW8693X integrates a high-efficiency boost converter as the H-Bridge driver supply rail. The output voltage, maximum current limit and maximum boost current are configurable. AW8693X features configurable automatically switch to standby mode after haptic waveform playback finished. This can less quiescent power consumption. The RSTN pin provides further power saving by fully shut down the whole device. Dedicated interrupt output pin can detect real time FIFO status and the error status of the chip. AW8693X features general settings are communicated via an I2C-bus interface and its I2C address is configurable.

Technical documentation
Type
Title
Date
Datasheet DS_AW8693X_EN_V1.7   2024-09-29
Product Design Guide AW8693X Software Design Guide   2024-12-02
Product Design Guide AW8693X Hardware Design Guide   2024-12-05

Design & development

For additional terms or required resources, click any title below to view the detail page where available.

Hardware development

Evaluation board

AW86937FCR V3.0 — It is suitable for performance evaluation board of Haptic chip AW86937FCR, and used with motherboard

AW86937 chip EVB evaluation board

View options
Software development

DRIVER OR LIBRARY

HapticHv_Drivers — Android drivers for Haptic_Hv series.

Android drivers for Haptic_Hv series, including sample code, porting guide, debugging guide, etc.

View options

APPLICATION SOFTWARE&FRAMEWORK

AW86937_GUI — AW86937 Tunning Tool

AW86937 GUI is a highly intergrated and easy-to-use tool for product configuration and debugging. Intuitive interface and uer-friendly operation can help customers shorten development cycle and complete system intergration quickly.

View options

APPLICATION SOFTWARE&FRAMEWORK

Haptic_M483KIDAE_MCU_FW — MCU common firmware for haptic EVB

MCU firmware for haptic EVB

View options
Hardware development

Evaluation board

AW86937FCR V3.0 — It is suitable for performance evaluation board of Haptic chip AW86937FCR, and used with motherboard

AW86937 chip EVB evaluation board

View options
Software development

DRIVER OR LIBRARY

HapticHv_Drivers — Android drivers for Haptic_Hv series.

Android drivers for Haptic_Hv series, including sample code, porting guide, debugging guide, etc.

View options

APPLICATION SOFTWARE&FRAMEWORK

AW86937_GUI — AW86937 Tunning Tool

AW86937 GUI is a highly intergrated and easy-to-use tool for product configuration and debugging. Intuitive interface and uer-friendly operation can help customers shorten development cycle and complete system intergration quickly.

View options

APPLICATION SOFTWARE&FRAMEWORK

Haptic_M483KIDAE_MCU_FW — MCU common firmware for haptic EVB

MCU firmware for haptic EVB

View options