AW86907FCR

11V Fast Startup With F0 Detect And Tracking LRA Haptic Driver

产品手册：

在线预览 - AW86907FCR - 产品手册

参考价格

1-99￥15.77
100-249￥12.93
250-499￥10.41
500-999￥8.20
1000+￥6.31

产品详细信息

参数

Voltage Type	Boost
Vout (Max) (V)	11
SRAM (kB)	12
Istandby (μA)	8
IO Level (V)	1.8<br>3.3
AAE	YES
Input Signal	IIC<br>3TRIG
LRA Calibration	LCC2.0
Temperature	-40℃~105℃
TikTap	YES
Package (mm)	FCQFN 2X3-20L

封装 | 引脚 | 尺寸

FCQFN 2X3-20L

特性

 1MHz I2C Bus
 12-KByte Memory
 12k/24k/48k input wave sampling rate
 F0 detect and tracking
 Advance autobrake engine integrated
 Playback mode:
 Real time playback(Up to 4KByte FIFO)
 Memory playback
 3 Trigger playback
 One wire playback
 Cont playback
 Resistance-Based LRA Diagnostics
 Drive signal monitor for LRA protect
 Drive Compensation Over Battery Discharge
 Fast Start Up Time ＜1ms
 Dedicated interrupt output pin
 Boost output voltage up to 11V
 VOUT=8.5V@Vbat=4.2V for 8Ω LRA
 Support automatically switch to standby mode
 Standby current：8μA @Vbat=3.6V
 Shutdown current：0.1μA
 Supply voltage range 3 to 5.5V
 Short-Circuit Protection, Over-Temperature Protection, Under-Voltage Protection
 FCQFN 2mm × 3mm × 0.55mm -20L Package

说明

AW86907 is a high voltage H-bridge, single chip LRA haptic driver, with F0 detecting and tracking based on BEMF, with a boost converter up to 11V drive voltage inside, supporting real time playback, memory playback, cont playback, one wire and hardware pin trigged playback. A typical startup time of 1ms makes the AW86907 an ideal haptic driver for fast responses. AW86907 integrates a 12KByte SRAM for user-defined waveforms to achieve a variety of vibration experiences, supporting 3 sampling rate(12k/24k/48k) of waveforms loaded in SRAM, supporting output waveform sampling rate up-sampling to 48k. AW86907 integrates an autobrake engine to suppress the aftershocks to zero for different drive waveforms(short or long) on different LRA motor. AW86907 supports LRA fault diagnostic based on resistance measurement and protections of short-circuit, over-temperature and under-voltage. AW86907 integrates a high-efficiency boost converter as the H-Bridge driver supply rail. The output voltage, maximum current limit and maximum boost current are configurable. AW86907 features configurable automatically switch to standby mode. This can less quiescent power consumption. Dedicated interrupt output pin can detect real time FIFO status and the error status of the chip. AW86907 features general settings are communicated via an I2C-bus interface and its I2C address is configurable. AW86907 is available in a FCQFN 2mm x 3mm x 0.55mm -20L package.

技术文档

类型	项目标题	语言	日期
产品设计指南	AW86905/7FCR应用设计指南	中文	2023-06-29
产品手册	DS_AW86907_EN_V2.2	英文	2024-01-03
技术帖	好用到“爆”的Trackpad是怎样实现的？背后原理请看这里！	中文	2023-02-28

设计和开发

如需其他信息或资源，请查看下方列表，点击标题即可进入详情页面。

硬件开发

评估板

AW869X7 V3.0 — 适用于Haptic芯片AW86907FCR/AFCR/BFCR、AW86917FCR/AFCR/BFCR、AW86927FCR的性能评估板，搭配底板使用

AW869X7系列芯片EVB评估板

了解详情

软件开发

驱动程序或库

HapticHv_Drivers — Haptic_Hv系列Android驱动。

Haptic_Hv系列Android驱动，包含Sample Code、移植说明、调试指南等。

了解详情

应用软件和框架

AW86907_GUI — AW86907调试工具

AW86907 GUI是高度集成工具，用于产品的配置和调试工程。直观的界面和人性化的操作，可以帮助客户缩短开发周期，快速的完成系统集成.

了解详情

硬件开发

评估板

AW869X7 V3.0 — 适用于Haptic芯片AW86907FCR/AFCR/BFCR、AW86917FCR/AFCR/BFCR、AW86927FCR的性能评估板，搭配底板使用

AW869X7系列芯片EVB评估板

了解详情

软件开发

驱动程序或库

HapticHv_Drivers — Haptic_Hv系列Android驱动。

Haptic_Hv系列Android驱动，包含Sample Code、移植说明、调试指南等。

了解详情

应用软件和框架

AW86907_GUI — AW86907调试工具

AW86907 GUI是高度集成工具，用于产品的配置和调试工程。直观的界面和人性化的操作，可以帮助客户缩短开发周期，快速的完成系统集成.

了解详情